Install rotisserie/rib-o-lator on a UDS..??

The friendliest place on the web for anyone that enjoys cooking.
If you have answers, please help by responding to the unanswered posts.

Jester1

Senior Cook
Joined
Jul 16, 2009
Messages
120
Location
Virginia Beach, VA
I just completed my UDS and now I'm if there is a way to install a rotisserie so that all you to do is to drill a hole on each side of the drum and mount the brackets..?? I have never owned a rotisserie setup so I was just thinking to could slide the rod from one end though the holes, then hook up the motor. Then when not in use you could seal the two holes up..?? I jsut don't really want to cut the notches in the drum because I wouldn't use the rotisserie all the time. Thanks again everyone...

Oh, I'm looking at the rib-o-lator....!!!

Jester
 
Home Depot sells the whole kit. I am drilling a 1/2 in hole in each side of the drum about 8 in from the rim. The adjacent hole will need to be a bit higher since the motor holds the rod higher than where the rod will rest on the other end. You can go higher with your holes since you are not using a flat stock drum lid. Mount the motor bracket with bolts and wing nuts so you can take the bracket off if you like. Use the wingnuts and bolts to plug those holes. I'm using 1/2 in metal plugs like the ones for the intake to plug the spit holes when not in use. The only bad thing is, you have to put your meat on the rod as it comes thought the hole into your drum, since you won't be able set it in slots. My buddy was joking that I’m going to drop a chicken into the burning charcoal basket! I might just use my bottom rack to prevent this. I also saw a Utube vid where a guy used Weber charcoal baskets on the sides of the bottom rack and a drip pan in the middle. Same set up as a kettle rotisserie.
Good Luck.
Mike
 
Personally, I wouldn't mount one in a drum. I'd much rather use a Weber rotisserie ring for it or any rotiss setup.

Couple of reasons and you can take it with a grain of salt.

1) Think about how you plan to fire the drum up with the rod mounted through the side.
2) Setting up the Rib-O-Lator IMO should be done on a flat surface and spin tested for balance.
3) Loading meats with the fire below will be HOT to work with and the possibility to lose meats is at risk.
4) I strongly encourage using a cook grate under any rotisserie on a drum.

img_215210_0_9ee92957a8d7655a2e15bdfb559d0759.jpg


img_215210_1_185c00de021098fda4180155818ff1f3.jpg


img_215210_2_e38c693687df4a2e85f483382956290f.jpg


img_215210_3_18c004fec9ba5dc0d8c35e99d54a8977.jpg


Char-Broil basket on the drum/w kettle ring

img_215210_4_4a4303443fd731bb3f26a9c151d6a744.jpg


Spit rod on drum w/kettle ring

img_215210_5_8db8aad570fc8bf129cfe5085cf5c9f0.jpg


Cajun Bandit w/R-O-L & Kettle ring

img_215210_6_ed3c13718506cca223870f8d34d8efc6.jpg


img_215210_7_5284f11e64c129a9004e1ab61dbadfe3.jpg


But-what do I know?

Rib-O-Lator Chief Charcoal Test Pilot
 
I don't think you can drill a hole in the drum and insert the rod. The rod would have to stick out both ends and with baskets or forks attached you wouldn't be able to slid it into two holes.
 
swamprb, thanks for all the pics... That just makes me even more excited about a rotisserie setup.

Bad thing is you all are probably right about needing a ring. I can definitely get another drum... I just really would rather not have to do another burn out. hmmmm.... the thinking and planning begins.
 
Keep an eye out for the Weber ring on E-bay or some other sites, I've seen them as low as $116 for the Ring, motor and spit rod.
 
I can definitely get another drum... I have a unlimited supply to drums as long as I'm not taking truck loads every week... I'll probably end up making a ring from another drum, I just need some time to get other things done around the house...
 
Back
Top Bottom